Electronic Component Identification | Quasar Electronic Kits Projects UK Electronic component identification and general information to assist in the assembly of Quasar Electronics kit ranges.

Electronic Component Identification

If you are new to electronics and kit building here is a brief introduction to electronic component identification. If you still need help please Contact Us.


Jump to   Bullet Resistors
Bullet Capacitors
Bullet Diodes
Bullet Transistors
Bullet Integrated Circuits
Bullet Miscellaneous



Standard resistors are NOT polarised and can be placed in the PCB either way round.

The most common have four bands. Bands 1 and 2 identify the first two digits, band 3 is the Multiplier and band 4 is the tolerance (normally Gold 5%)

The Multipliers are:

R = x 0

K = x 1,000

M = x 1,000,000

The kit parts list might contain for example, a 4K7 resistor. The K refers to the number multiplier (K = x 1,000). The position of the K between the 4 and 7 identifies the position of the decimal point so we have

4.7 x 1,000 = 4,700 Ohms (with a colour code of Yellow, Violet, Red)

Another example is say 56R. This gives us 56 x 0 = 56 Ohm resistor with colour code Green, Blue, Black.

You will find some five band resistors in our kits and this colour code is likely to be associated with the more precision 1% and 2% types. The work in a similar way to the four band but the first three bands are used to determine the numbers, band 4 is the multiplier and band 5 is the tolerance - see table below for details. Your "garden variety" 5% general purpose types will be four band resistance codes.


Resitor colour codes chart

Resistor Networks

Many resistor networks have an orientation marked with a dot at the end of one side. This dot must be marks pin 1. This pin is marked on the PCB by a square box at one end of the main box.



Capacitor conversion table

Capacitors values may be designated in micro-farad (uF), nano-farad (nF) or pico-farad (pF) and there is a certain amount of overlap. There are many instances where two components of the same value may be quoted in different ways: one may be quoted in terms of pico-Farads and another in terms of nano-Farads. For example 100 nF is the same as 0.1 micro Farads. The chart below quickly helps show what which values are the same and how many nano-Farads makes a micro-Farad and so forth. It can be used as a quick reference guide for capacitors, or any other electronic component when looking at different items from different manufacturers.


Capacitor conversion table for pico-Farads, nano-Farads, and micro-Farads

micro-Farads (µF) Nano-Farads (nF) Pico-Farads (pF)
0.000001 0.001 1
0.00001 0.01 10
0.0001 0.1 100
0.001 1 1000
0.01 10 10000
0.1 100 100000
1 1000 1000000
10 10000 10000000
100 100000 100000000


Using the capacitor conversion table it is possible to quickly check the relationship between two capacitors with different markings. In this way it is possible to see whether they capacitor values are the same or not.


Electrolytic & Tantalum Capacitors

Electrolytic and tantalum capacitors are POLARISED devices which means they must be inserted with the correct polarity.

Electrolytics have one lead longer than the other and this denotes the POSITIVE lead and on the opposite side of body is a black band with a minus sign.

Tantaulm beads have a + sign next to the positive lead.


Ceramic Capacitor Codes

How to read a Ceramic capacitor with Numeric coding.

Ceramic Capacitor Codes

Multiplier Table (Ceramic)

Number Multiply By (Additional # of Zeros)
0 None (0)
1 10 (1)
2 100 (2)
3 1,000 (3)
4 10,000 (4)
5 100,000 (5)
6 1,000,000 (6)


Common Temperature Coefficient Codes (Ceramic)

Code Tolerance
C 0.25pF
J 5%
K 10%
M 20%
D 0.5pF
Z +80% / -20%




All diodes are polarised and must be inserted with the correct orientation to avoid damage to the circuit.

Signal &Y Power Diodes

Diodes are polarised and need to be inserted with the band marked at one end of the body (the cathode) to the band marked on the PCB.

Diodes come all all shapes and sizes but the ones used most often in our kits are 1N4148 signal diodes (orange body with blank band) and 1N4004 rectifier diodes (black with silver band). Both are marked on the body with their part number.

Zener Diodes

You may also find Zener diodes. These look similar to the 1N4148s and are easily muddled up! The voltage is marked on the body e.g. a 5.6V Zener will have 5V6 on the body.

Light Emitting Diodes (LEDs)

Light Emitting Diodes (LEDs) are found in many kits. They are normally red in colour but green and yellow are also sometimes used. LEDs are polarised and must be inserted the correct way.

The negative (cathode) lead is indicated in most cases by a "flat" on that side of the body. This flat is also indicated on the PCB legend for orientation purposes. You may also find that the positive (anode) lead is indicated on the board, corresponding to the long leg of the LED.



Transistors come in a wide variety of shapes and sizes. The flat side on small diodes (like BC547, BC548 and BC557 in TO-92 packages) denotes the orientation. Just match up the flat on the transistor to the flat on the circuit board legend taking care not to cross any of the legs over.


Integrated Circuits

Most Integrated Circuits (ICs) are STATIC SENSITIVE and correct anti-static handling procedures must be observed to avoid damaging them. You might wish to invest in one of the HTS131 Anti-static Wrist Bands that we sell.

Most ICs supplied in our kits are standard DIP Dual Inline Packages.

Unless otherwise instructed ICs should only be inserted once assembly has finished and the board tested (check the voltages present in the IC socket are correct before proceeding). It is important to remove all packing materials including silver foil before inserting the ICs into the IC socket or board. NEVER insert or remove an IC when the board is powered up.

To ensure correct orientation, identify the notch or dot at one end of the body. Pin 1 of the IC is to the left of this marking. Match this to the notch on the board legend and insert the IC, taking care not to bend the legs.

If you need to remove an IC you can use a flat bladed screwdriver. Slide it between the IC socket and the body of the IC and slowly prise it out. Take you time and certainly DO NOT try to pull it out will pliers otherwise you will break legs off.



Quasar Electronics Limited
Your Cart
Your Cart: Empty
© 2017 Quasar Electronics Limited, all rights reserved worldwide.
Exec Time: 0.093981 Seconds Memory Usage: 4.81971 Megabytes