AC Motor Speed Controller (DC Signal/Pot) Module, 230Vac 50Hz, 2500W AC Motor Speed Controller (DC Signal/Pot) Module, 230Vac 50Hz, 2500W Cebek This external signal (0-10Vdc) or potentiometer operated AC motor speed controller uses a triac output and allows you to adjust the speed of 230Vac 50Hz single-phase "universal" motors as used in power drills, vacuum cleaners, etc and an operating load of u... Electronics > Circuit Components > Printed Circuit Boards > Development Boards cebek_r_26 R-26 47.90 Quasar Electronics Limited https://www.quasarelectronics.co.uk/Item/cebek-r-26-ac-motor-speed-controller-dc-signal-potentiometer-module-230vac-2500w
Location
Home / Electronic Kits & Modules / Motor Controller - Driver Kits / AC Motor Speed Controller Circuit Boards / Cebek R-26 (CR026) - AC Motor Speed Controller (DC Signal/Pot) Module, 230Vac 50Hz, 2500W

AC Motor Speed Controller (DC Signal/Pot) Module, 230Vac 50Hz, 2500W

Cebek R-26 (CR026) - AC Motor Speed Controller (DC Signal/Pot) Module, 230Vac 50Hz, 2500W
Cebek R-26 Electronic Module (Pre-Assembled)
Cebek Electronic Modules

This external signal (0-10Vdc) or potentiometer operated AC motor speed controller uses Phase Angle Regulation (PAR) and a triac output and allows you to adjust the speed of 230Vac 50Hz single-phase "universal" motors as used in power drills, vacuum cleaners, etc and an operating load of up to 2500 Watts.

Motor speed adjustment is from 0 to 100% is achieved using either an external 10K potentiometer (not included) or a 0-10V dc control signal. The dc control signal input is electrically isolated from the mains.

Signal input operation can be set so the output is either directly or inversely proportional to the control signal.

Please see User Manual below for full description.

PRODUCT SELECTION NOTES: Suitable for controlling most 230Vac 50Hz single-phase "universal" motors, light regulators, 230V signals through automatisms, etc. NOT suitable for use with synchronous AC motors, capacitor-start/run AC motors or inductive loads like halogen or PL lamps, neon, etc.. Ask the manufacturer to confirm if their motor is suitable for control using a Phase Angle Regulation (PAR) style controller BEFORE you buy this product! The motor controller should have an output load capacity at least 25% above the motors peak power requirement. Please do NOT rely on motor rating plates for power consumption figures as they often quote average not peak power. You should verify the actual peak power at start-up and under full load before selecting an appropriate size motor controller.

Suitable for use with DIN-RAIL Mounting (Order Code C7589).

Please see CR027 for a 5000W version of this product.

Features
  • Please note that we will not ship this item to customers outside of Europe
Specifications
Operating Voltage230Vac 50Hz mains (the interference filter mentioned in the User Manual is optional and is not necessary in most installations)
Output Load2500 Watts maximum
Control signal voltage0 - 10V dc
External potentiometer10K Ohm (Order Code RE.POT.10KLIN)
Output Load (Minimum)50 Watts
Operating Voltage (Minimum)90Vac
Board Dimensions (mm)~ 121 x 107 x 45 mm
Product FormatPRE-ASSEMBLED Electronic Module Product Format Info
WARNINGThis product operates at mains voltage. Installation, testing and commissioning should only be attempted by competent persons, or under supervision of someone fully experienced in this field. Many areas of the assembly (including heatsinks) may operate at mains voltage. It must be fitted into a suitable isolating enclosure to avoid injury or death. Mains Electricity Info
Item Number:
Cebek R-26 (CR026)
Your Price:
£39.92 +VAT, £47.90 Inc
Stock Info:
In Stock
Your Total:
Quantity:

You might also like . . .

10K 16mm Linear Potentiometer

10K Ohm 16mm Linear Potentiometer...

£0.79 +VAT, £0.95 Inc
In Stock
AC Motor Speed Controller Module, 230Vac 50Hz, 1500W

1500 Watt, 230Vac motor speed controller allow you to adjust the speed of single-phase "universal" motors as used in power drills, vacuum cleaners, etc. Speed adjustment is controlled using a Triac output and a potentiometer mounted on the board...

£12.94 +VAT, £15.53 Inc
In Stock
AC Motor Push-Button Speed Controller Module, 230Vac 50Hz, 1500W

This push-button operated AC motor speed controller uses a triac output and allows you to adjust the speed of 230Vac 50Hz single-phase "universal" motors as used in power drills, vacuum cleaners, etc and an operating load of up to 1500 Watts...

£28.53 +VAT, £34.24 Inc
In Stock
AC Motor Speed Controller (DC Signal/Pot) Module, 230Vac 50Hz, 1500W

This external signal (0-10Vdc) or potentiometer operated AC motor speed controller uses a triac output and allows you to adjust the speed of 230Vac 50Hz single-phase "universal" motors as used in power drills, vacuum cleaners, etc and an operating load of u...

£29.21 +VAT, £35.05 Inc
In Stock
AC Motor Speed Controller, DC Signal/Pot 230Vac, 5000W

This external signal (0-10Vdc) or potentiometer operated AC motor speed controller uses a triac output and allows you to adjust the speed of 230Vac 50Hz single-phase "universal" motors as used in power drills, vacuum cleaners, etc and an operating load of u...

£52.90 +VAT, £63.48 Inc
In Stock
DIN RAIL Mounting, 107 x 121.25 mm

DIN RAIL mounting support for 107mm wide x 121.25mm deep printed circuit boards. Allows you to mount the PCB onto a DIN-RAIL in an easy, secure and economical manner. Support is supplied with the base, two lateral parts and feet...

Buy 1-13: £7.46 +VAT, £8.95 Inc Each
Buy 14-34: £7.27 +VAT, £8.72 Inc Each
Buy 35+: £7.09 +VAT, £8.51 Inc Each
In Stock
Quasar Electronics Limited
Your Cart
Your Cart: Empty
Search
Categories
© 2017 Quasar Electronics Limited, all rights reserved worldwide.
Exec Time: 0.118515 Seconds Memory Usage: 6.152245 Megabytes